|
 |
Style P201 workstation luminaires feature an integral hang-on mounting channel that facilitates installation on open office furniture panels. They are designed to provide low-glare task lighting for horizontal worksurfaces. Where privacy partitions occur, these luminaires also reduce workstation luminance ratios by softly lighting the panel in front of the user. |
|
| Features |
 |
 |
| Dimensions and Lamping |
|
| Six standard lengths are offered with full length lamping. Non-standard lengths from 35-3/4" to 95-3/4" at 1" increments are available at an additional cost. |
Design Tip:
Mounting methods that engage system furniture support features may dictate a non-standard luminaire length. |
| Each luminaire is provided with one T5 fluorescent lamp or two tandem mounted T5 lamps according to the overall luminaire length. To limit the luminance of workstation surfaces, only standard output lamps are offered. The use of high-output T5 lamps is not recommended. |
|
|
 |
|
| Length |
|
Lamps |
Input |
| 35 3/4 ″ |
(908 mm) |
1xF21T5 |
27 watts |
| 47 1/2 ″ |
(1206 mm) |
1xF28T5 |
34 watts |
| 59″ |
(1499mm) |
1xF35T5 |
40 watts |
| 70-3/4″ |
(1797mm) |
2xF21T5 |
52 watts |
| 82 1/2″ |
(2096mm) |
1xF21T5 + 1xF28T5 |
61 watts |
| 94 1/4″ |
(2394mm) |
1xF28T5 |
66 watts |
|
|
3000K lamps are included. 3500K and 4100K lamps are available upon request.
Non-standard lamp configurations are available on large quantity orders (e.g. 71" luminaire with 1xF35T5 lamp). Consult factory. |
|
|
| Mounting Height |
|
Recommended mounting height is 48" to 50" A.F.F. for 24" deep worksurfaces and 48" to 52" for 30" deep worksurfaces (based on a worksurface height of 28-1/2" and a minimum seated eye height of 40-1/2"). When a standard desk clamp stanchion is used, top of the luminaire is at 48" A.F.F. (19-1/2" above the worksurface).
Tambient can provide non-standard task lighting optics for certain other workstation geometries.
Contact Tambient for details.
|
|
 |
Caution: To avoid discomfort glare, do not install these units above 52" A.F.F. (50" for 24" deep worksurfaces). |
|
|
|
| Mounting Accessories |
|
| Ballasts |
|
Luminaires are supplied with integral 120 volt, high power factor electronic ballasts for energy efficiency.
Programmed start ballasts are standard to maximize lamp life and minimize energy use.
Manufacturer/model of furnished ballast(s) may vary. However, all ballasts furnished meet or exceed the following criteria: |
|
 Total Harmonic Distortion (THD) < 10% |
| Power Factor (PF) > 97% |
| Ballast Factor* (BF) > 98% |
| Current Crest Factor (CF) < 1.7 |
| Sound Rating A or better |
| ANSI, IEEE, and FCC compliant |
| UL listed (United States and Canada) |
| *Primary lamp application |
|
|
|
| Cords |
|
| Cords are factory installed, 18 gauge, 3-conductor, Type SJT with grounded plug in accordance with UL153 (Standard for Portable Electric Luminaires) and the associatedSupplementary Requirements for Units for Use with Office Furnishings. |
|
Furnished cord length is 9 feet; the maximum length allowed by the standard. Standard cords are black. Gray and beige cords are available at an additional cost.
A choice of straight and sw rotation plugs is offered.
|
|
| For installations in the City of Chicago, we offer cords with a circuit breaker in the plug to comply with the Chicago Electric Code. Chicago cords are offered in straight plug and sw rotation plug versions. However, Chicago cords are available in black only. |
|
 |
|
The sw rotation plug allows two low-profile plugs to engage adjacent outlets in one duplex receptacle while managing cords close to walls and office partitions. |
| Straight plugs are often best for use with power outlets in recessed floor boxes and access flooring systems. |
 |
|
All cord plugs are NEMA 5-15 configuration and require a compatible grounded electrical receptacle (by others).
|
|
|
|
| Cord Exit Locations |
|
| Cord exits are concealed in a unique multi-purpose mounting slot at the rear of the luminaire. The slot contains cord management features allowing the cord to be routed horizontally (right or left) to any drop location, even when mounting accessories are inserted into the slot. |
|
| To maximize cord utilization, right hand and left hand cord exit locations are available. |
 |
 |
|
 |
|
|
|
| Finishes |
|
| 6-stage pretreatment and electrostatically applied thermoset powder coat provides a stable, long-lasting and corrosion resistant finish. |
Standard finishes: |
 |
|
Note: These photos give the viewer a general impression of the color selections available. Due to variances in computer monitors, video cards, and color printers, they should not be used for color matching in critical color situations. To order a color sample for review, please submit a sample request form. |
|
|
Non-standard finishes:
RAL color finishes are available for a set up charge of $300 per run. RAL finishes are Tiger Drylac® Series 49 formulations and have a smooth glossy finish. Contact your nearest Tiger Drylac® office to obtain color samples. For non-RAL colors and other gloss factors specify a custom color finish. Preview RAL colors
Custom color finishes are available for a set up charge of $750 per run. You must submit a color sample for Tambient to consider your custom color request.
|
|
|
| Decorative Endplates |
|
Decorative endplates are available and must be ordered separately. They install easily over the standard black endplates with a single concealed screw to form a decorative reveal. Decorative endplates add 3/8" (each) to the luminaire length.
|
Note: Luminaires with decorative endplates cannot be end-mounted. Decorative endplates can be removed to allow for end mounting if luminaire length corresponds to mounting location. |
|
 |
|
|
| Safety Standards |
|
| All Tambient luminaires are UL listed to comply with United States and Canadian standards. |
|
 |
|
